Reviews for Quadratec Pre-Runner LED Light Bar Kit for 07-18 Jeep Wrangler JK

Did not fit my vehicle.

Easy to install and looks great. Just started to have the lights stay on even after parking lights are off?

Install went super smooth. Everything lined up well and mounted solidly.
A little bit of an effort to get the wire harness routed around the driver's headlight, but no biggie.

I have after market grill so I had to improvise Makes a lot of difference.Installing wasn’t the problem but removing the side marker might require a plier .is worth the price

Cool light upgrade. Easy to install. The only reason I didn’t give 5 stars was because I had to wait for the bracket. It didn’t come with the lights. The had put in a LED FLASHLIGHT instead of the bracket.

I was able to do a mod around my after market hood lock and install the light kit. Purchased 3" brackets from big box store and modified them to work for this install. These lights set behind my inserts without issue. Did have an issue getting the wiring connectors of the lights to perfectly match up to oem marker light connector. Used good quality electrical tape resolved the issue if the connector not wanting to stay connected. Quadratec needs to sell an adaptor kit for pre-runner lights that accommodates after market hood locks, due to hood lock popularity ;).

This light kit is very cool looking. Definitely makes the Jeep stand out from the rest. They're bright too. They don't get washed out by my super-bright LED head- and fog lights.

I can't give it five stars though, only because there are some installation bugaboos they don't tell you about. The light bar mounts with nut-clips on two tabs on the radiator support. On my vehicle, the factory wire loom was attached to those supports with ring fasteners. In order to move the factory loom out of the way as stated in the instructions, I had to break the fasteners to release the loom, then pull the broken fasteners from the tabs. I also had to do the same to two more fasteners on the far sides of the radiator so I could move the loom enough out of the way to get enough room for the light bar to fit. Once the bar was in though, it was simple to just wire-tie the factory loom to the bar.

Also, the right side of the light bar didn't quite clear the plastic bracket in front and above the radiator, even with the bar moved as far right as possible. I had to shave a small bit of the bracket away to get it to fit.

And, it's not as easy as you might think to get the individual lights out of the grommets and pull the kit's wire loom back enough to drop the wires into the receptacles, seat the grommets and re-seat the lights in the grommets. In fact, the kit's wire loom was taped together at the end, and the tape needed to be pulled off before attempting the whole kit assembly. For the life of me, I don't understand why this kit isn't fully assembled from the factory.

So, when purchasing this kit, know that there might be some installation issues not covered in the manual. But it's all worth it for how it make the Jeep look...

Awesome light addition to your 07-18 Jeep Wrangler. Easy to install and looks GREAT!! Tok about 45 minutes to install. Note... does not come with allen wrench. Allen screw is a-typical size, so I needed to get my own screws to fit clip. Also, you will need to move existing harness to under the pre-runner light assembly and then re-wire tie everything when finished. If you don't, prerunner light assembly will be bent. Wireties fit existing jeep locations after you remove them when you cut them. A must have for your Jeep!

This would be a 5 star, however it didn’t come with the hardware needed to connect the assembly to the vehicle. As a result of this, I needed to use zip ties to connect. Then an additional zip tie in the middle to hold it stable and level. I like for my additions to my Jeep to be added cleanly and correctly and this obviously is not.

However I must say, once this is installed it looks great on the vehicle. Lights are bright enough that they aren’t over powered by my led headlight and fog lights. I also have honeycomb grill inserts and the lights are still clearly visible.

Just make sure you have all the parts before you assemble.

would have been an easier install had I had all the pieces and directions, missing retaining clips and bolts. looks great.